Ҳамаи категорияҳо
EN

Асосӣ>ахбор>Хабарҳо саноат

Маҳсулотҳои гарм

  • AB-51 ~ 53
  • AB-460 ~ 463

бо мо тамос гиред

ADDRESS:№ 89, Роҳи Ежанг, Ҷамоати Вуқиао, Таун Чжуанг, ноҳияи Фенгсян

Тел:021-57407335

E-MAIL:[почтаи электронӣ ҳифз карда шудааст]

Чӣ гуна истеҳсолкунандагони хӯлаи рехтагарии рехтагарӣ ҳубобҳои ҳаворо ҳал мекунанд?

Вақт: 2020-06-03 Хитҳо: 20

Zinc alloy is an alloy composed of zinc added with other elements. Zinc alloys are easy to form, have strong plasticity, low cost, high processing efficiency, and a wide range of applications. However, the foaming problems (electroplating and spraying) of Jiangmen zinc alloy die castings are some problems. So how to solve the cause of blistering? The following points:

  

1. Product design

When the design of zinc alloy die-casting products begins, it is necessary to consider the feed port, slag discharge port and exhaust setting of the die-casting mold. Because the flow path of the workpiece for feeding and slagging is smooth, there is no air entrapment, no water stains, and no dark bubbles, which directly affects whether the subsequent electroplating blisters. Qualified feeding and slagging. The mold is die-casted. , No water stains.

  

 2. Development of die casting mold

In the development of die-casting molds, the tonnage, pressure, insufficient pressure, and poor exhaust of the molding machine should also be considered. No matter how the pre-treatment of the plating is solved, there is always 20-30% blistering. The mold is blocked and changed to a few Pieces, no re-bubbling after plating.

 

3. Pre-treatment surface

The pre-treatment surface of the polishing liquid, polishing paste, and oxide layer are not cleaned, and there is often rolling. The zinc alloy die-casting after rolling is bright. Many employees in the electroplating plant pickling process are pickled casually. The polishing agent attached to the surface is not washed, and blistering often occurs. In addition, the calender used by the calendering and polishing plant also has a great relationship, and some surfactants in the calender are difficult to wash.

 

4. When the product enters alkali copper

Before the product enters the alkali copper plating tank, the zinc alloy die-casting parts still have a black film that is not treated with oxide film to remove wax and oil. Therefore, the removal of the membrane is very critical. In the early years, it can be removed by using anti-staining salt. The current environmental protection does not allow the discharge of wastewater containing anti-staining salt.

  

5. Alkali copper plating tank

There are many organic substances in the alkaline copper plating tank, and there are many impurities, and the free cyanide is not in the range. Test the ingredients of the alkaline copper tank to see if the sodium cyanide is low or the sodium hydroxide is high! Very critical, it is recommended to treat the carbon once every 3-5 days.

  

6. Conductivity of alkali copper cylinder

The conductivity of the alkaline copper cylinder is also very important. Whether the anode is dissolved properly and the anode copper plate is sufficient will lead to blistering.

  

7. The product foams after coming out of the oven

It may be caused by the uneven temperature of the oven, that is, the temperature is too high. Due to the lack of tightness during die casting, it is easy for acid to enter the water stained trachoma of zinc alloy die castings.The acid and zinc will still react chemically even if there is a surface coating, generating a large amount of hydrogen H. When the pressure inside is higher than atmospheric pressure To a certain extent, adding high temperature will produce bubbles.

Professional manufacturer of zinc alloy die casting: Hoshimoto CO.,Ltd    www.hoshimoto-sh.com

БО МО ТАМОС ГИРЕД